death 2 zograma 
death 2 zionazi scum
it wasn't squirting so I filled it and then it still wasn't squirting so later I looked in there again and it had all drained out, what an antisemitic waste of a couple shekels 
I don't have any car cowtools 
and I didn't look under the car but I assume there must be a gaping hole at the bottom for it all to drain so quickly 
so do you think I can fix it myself or do I have to get wallet r*ped at mechanic 
it's winter so it's kind of necessary to be able to see ig
Jump in the discussion.
No email address required.
nothing was coming out so I lifted the hood and it looks empty now
Jump in the discussion.
No email address required.
Ok. Unfortunately that doesn't tell us much.
If you fill it to the brim, then let it sit overnight without touching anything, does the level go down?
Yes: The reservoir is cracked, or the pump gasket is bad.
No: Your reservoir is intact. When you push the button, washer fluid is being pumped but leaking somewhere else.
There's a couple common failure points, depending on the vehicle: An anti-drainback valve, the T-fitting where it splits between the two nozzles, or the nozzles themselves.
I don't know what year your Mazda is, but I've had this happen on my 2010 Milan and my 2016 Flex. Usually right around the 7-8 year mark, the ethanol in the washer fluid finally degrades the fittings and they begin cracking. It's worth noting that a 2010 Milan is basically an americanized Mazda6.
Jump in the discussion.
No email address required.
omg thanks, i'll try to fill it again and leave it alone tonight. I had tried using it several times bc I thought the issue was just that it was empty (it was empty)
it's a 2012, so pretty old and I bought it used this summer
Jump in the discussion.
No email address required.
Ok, so looks like yours has the nozzles in the cowl, and check valves and all that.
It'd be worth seeing if washer fluid is building up in the cowl area when you run the pump. I don't have my Milan anymore, but lemme go snag pictures of my Flex since that's also cowl-nozzled.
Blue is reservoir, pink is where it heads into the cowl, yellow is nozzles. A butter knife or flat screwdriver can release the pins holding the cowl on
In the cowl, you can see the fittings and whatnot where it's probably leaking
If you've never dealt with them before, these fasteners are in two parts. Lift up the top portion, then the whole body.
Jump in the discussion.
No email address required.
I filled more fluids and left it overnight and it looks like it drained again
sorry it's so dirty
maybe the fittings are also cracked though, I didn't check that far :<
Jump in the discussion.
No email address required.
So then we'd have to see about getting to the pump, determine if the bottle is cracked or if the rubber grommet on the pump is leaking.
There's a couple different reservoirs for a 2012 mazda3 -- sedan small, sedan large, and hatchback. This is what the small sedan looks like, the black bit is the pump.
Might be accessible from underneath but if you're climbing under the car, NEVER rely on a jack of any sort. They can, and do, fail without warning. Jackstands save lives. Lacking that, you could also find a small overhang/curb/2x4s to drive up, then set the parking brake (if functional) and chock the rear wheels.
I'll trade you, though. I'd rather be diagnosing a plastic bottle than replacing strut mounts. This is what my morning looks like. You can see I have a jackstand, and my tire just as a backup if it slips off the stand somehow -- I'd rather buy a new tire than a new spine.
Jump in the discussion.
No email address required.
the blue thermometer thing also keeps coming on and off randomly
idk if it's related
apparently canadian tire lets you borrow cowtools, maybe I will do that and learn to be less r-slurred
it's nice you know what you're doing, you probably save thousands from avoiding (((mechanics)))
Jump in the discussion.
No email address required.
Oh Canada? Ok good, I thought you were in Africa or something. Yeah I think Canadian Tire loans cowtools.
The blue thermometer means the engine is still cold, that's perfectly normal. Some manufacturers switched to that because it was cheaper than adding a separate temperature needle.
Jump in the discussion.
No email address required.
giving off afrikang vibes makes me sound way cooler than I am so I will take it
I looked it up and google said that my coolant is leaking and my engine is overheating and I need to go to a mechanic immediately or it will have to be towed, kill all google "engineers"
Jump in the discussion.
No email address required.
More options
Context
zoz
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
omg thank you so much you're the best 💓💗💖 I have to go out but I'll film what's inside later
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context