That was the wrong link sry, meant to link to acrylic adhesives cartridges.
V-groove it to 90% depth with a brand new acute cone carbide burr on a dremel. There's no other way to get a proper bond in a crack. If you try disassembling it you will only create new leak paths.
Jump in the discussion.
No email address required.
Using drone + laser measurements to map out the deck I need to replace. Still going to be a b-word figuring out how many boards I need to pick up.
Jump in the discussion.
No email address required.
Based on this incomplete butt drawing and your c*m enducing video, the answer is one hundred eighty five (185) 2x6x20s.
Jump in the discussion.
No email address required.
More options
Context
Should be about 70 1x4x8ft deck board but buy 60 to start
Jump in the discussion.
No email address required.
More options
Context
Just count them. You're over thinking it.
Jump in the discussion.
No email address required.
More options
Context
More options
Context
what more does a man need
Jump in the discussion.
No email address required.
Apparently a case of dew and a drone to make a shitty map when a tape measure would do just fine.
Jump in the discussion.
No email address required.
More options
Context
More options
Context
Don't let the poors steal your cabinets
Jump in the discussion.
No email address required.
More options
Context
Nice hardwood homie. Red oak?
Jump in the discussion.
No email address required.
Looks like laminate lol.
Jump in the discussion.
No email address required.
More options
Context
Wait. There's some kind of oak in the main areas. Not sure.
Jump in the discussion.
No email address required.
More options
Context
More options
Context
Kino
Jump in the discussion.
No email address required.
More options
Context
Nice bro
Jump in the discussion.
No email address required.
More options
Context
Woot important question, what would you recommend I use to seal a crack in my headlight lens?
I drove through heavy rain and now the entire housing is like, soaked on the inside.
Jump in the discussion.
No email address required.
Any UV stable epoxy. Going to be hard to find one you don't have to spend $250 buying in bulk.
Jump in the discussion.
No email address required.
Shit. It's at an edge but new housings are hard to come by.
Jump in the discussion.
No email address required.
https://multimedia.3m.com/mws/media/530755O/3mtm-optically-clear-adhesives-8211-8212-8213-8214-8215.pdf
Jump in the discussion.
No email address required.
That appears to be more like a tape, which won't seal properly on this edge.
I may have to bake the light open and coat it or something.
Jump in the discussion.
No email address required.
That was the wrong link sry, meant to link to acrylic adhesives cartridges.
V-groove it to 90% depth with a brand new acute cone carbide burr on a dremel. There's no other way to get a proper bond in a crack. If you try disassembling it you will only create new leak paths.
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
Pizza has the sexier voice, but I would pick you any day for your raccoons and general non-awfulness.
Jump in the discussion.
No email address required.
More options
Context
Where's your beer? I'm an acual landlord btw. No larping from me.
Jump in the discussion.
No email address required.
More options
Context
I love you.
Jump in the discussion.
No email address required.
More options
Context
That deck do be needing a lot of work, ngl
Jump in the discussion.
No email address required.
More options
Context
Do not be misled: "Bad bussy corrupts good bussy." 1 Corinthians 15:33
Jump in the discussion.
No email address required.
More options
Context