Blunt knives are infinitely more safe for precision work, because A) You should never be using enough force on resin or plastic to make a difference B) You always want to cut towards a bracing finger or thumb for maximum control and C) Razor sharp blades can easily tilt and obliterate a chunk of resin or gouge where a mouldline is before you even realize it was tilted.
Jump in the discussion.
No email address required.
Jump in the discussion.
No email address required.
either you suck at shaving or you
without a lot of forethought
Jump in the discussion.
No email address required.
Nah I was using them to remove the supports from some prints and the blade
slipped. There 
was blood 
everywhere.
Jump in the discussion.
No email address required.
do you not have any kind of store near you?
Jump in the discussion.
No email address required.
These are for next time. I had enough
but I'm running 
low
Jump in the discussion.
No email address required.
Last time I ran low on bandaids I just put it on my shopping list and bought some the next time I went to the supermarket (a couple days later).
Jump in the discussion.
No email address required.
The price is exactly the same plus I'm not going
to the store for a few days. And I'd have to go to the drug store for quick 
clot
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
I don't think Amazon supports our area yet.
Jump in the discussion.
No email address required.
Where do you live?
Jump in the discussion.
No email address required.
It's all too hazy to remember.
Jump in the discussion.
No email address required.
Lying bot
Jump in the discussion.
No email address required.
I think you should learn to code better
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
did you died?
Jump in the discussion.
No email address required.
No I was able to clean
it up. But I almost ran out of quick 
clot and extra large 
bandaids.
Jump in the discussion.
No email address required.
More options
Context
More options
Context
Oof.
Once I was scraping the purge line the long way and it slid all the way under my fingernail. Now I always scrape sideways.
Jump in the discussion.
No email address required.
If you clamp your fingernails soon enough
and don't stress them for a few days they'll reattach. It took me a few tries to figure 
that one out
Jump in the discussion.
No email address required.
idk how your printer is set up, but mine prints a really thin line. it was a single shoot up the nail. never had a nail come off thank god
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
Lmaoing at you.
Jump in the discussion.
No email address required.
It's much safer than a blunt
one
Jump in the discussion.
No email address required.
Tell that to the slice in your hand r-slur.
Blunt knives are infinitely more safe for precision work, because A) You should never be using enough force on resin or plastic to make a difference B) You always want to cut towards a bracing finger or thumb for maximum control and C) Razor sharp blades can easily tilt and obliterate a chunk of resin or gouge where a mouldline is before you even realize it was tilted.
Jump in the discussion.
No email address required.
Jump in the discussion.
No email address required.
Nah frick that advice. A is correct, but B is completely backwards. C comes with A.
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
What printer you run? Assuming nobody else bought it yet im getting a bambu p1p tomorrow and im suuuper excited.
Jump in the discussion.
No email address required.
Tina
I bought her for $110 a while ago. I've never
needed to print 
something larger than 4x4x4 so I haven't upgraded yet.
Jump in the discussion.
No email address required.
More options
Context
NGMI, genuinely. you'll need to debug something and quit
Jump in the discussion.
No email address required.
B-word i got my modded to heck ender 3 already. Ive done my time.
Jump in the discussion.
No email address required.
the most popular printer of all time. Wow!
Jump in the discussion.
No email address required.
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context
More options
Context